Hemp Dryers / Hemp Sorters

Hemp Sorters

Hemp sorters (sometimes called bud sorters) sort whole flower buds by size. By passing hemp over vibrating screens of increasing mesh, over-sized buds are ejected out the side of the unit and under-sized pieces pass through the screen for further sorting. Available in sizes from 18” in diameter to 100”, a single unit can divide product into 5 classifications and be used for multiple product types. Screens are easily swapped and available in mesh sizes from inches to microns.

Circular vibratory sorters are preferable to the original rectangular and manual models for high-throughput applications because of their large capacity, ability to run continuously, and little need for operator supervision. The circular design maximizes surface-area utilization, is easier to clean, and minimizes the distance product must travel before being classified.

Product Details

Standard Sizes & Features

Small Hemp Sorter

24” diameter 2-Deck High Efficiency Budsorter
One 4” high top spacing frame with a 6” diameter oversize discharge spout
One 4” high middle spacing frame with a 6” diameter product discharge spout
One 6” high discharge frame with a 6” diameter side discharge spout
Open Top (No Cover)
Four special metal screens and two wire mesh screens for installation of two at a time depending upon product being screened (mounted on standard tension rings with food grade gaskets).
Two (2) Quick Acting Clamp Ring Assemblies at screen sections
304 stainless steel product contact parts
Food Grade Glass bead Finish on frames
Epoxy coated carbon steel caster base and motor support table
½ HP, 230 volt, 3 phase, 1800 RPM, 60 HZ TENV motor
Motor Inverter will be included

Large Hemp Sorter

K40-2-SS, 2-deck Vibroscreen, 40” diameter 2-Deck Kason, High Efficiency Large Budsorter
One (1) 6” high top spacing frame with an 8” diameter oversize discharge spout
One (1) 6” high middle spacing frame with an 8” diameter product discharge spout
One (1) 6” high discharge frame with an 8” diameter side discharge spout
Open Top (No Cover)
Four (4) special metal screens and two (2) wire mesh screens for installation of (2) at a time depending upon product being screened (mounted on standard tension rings with food grade gaskets).
Two (2) Quick Acting Clamp Ring Assemblies at screen sections
304 stainless steel product contact parts
Food Grade Glass bead Finish on frames
Epoxy coated carbon steel caster base and motor support table
½ HP, 230 volt, 3 phase, 1800 RPM, 60 HZ TENV motor
Motor Inverter will be included

 

Options

Units are available in sizes up to 100" inches in diameter and can accommodate most high-throughput applications

CIP (Clean-In-Place)

Our hemp sorters feature leak-free nozzles positioned at all screen surfaces which blast typical sticking-points with solution and/or steam. Interlocking flanges bridge the gap between screen meshes and walls which exist in the other bud sorters. This minimizes ingress and streamlines cleaning.

Variable Vibration Patterns

The unevenly-weighted gyro-motor is adjustable and capable of various oscillation patterns. This prevents milled hemp and buds alike from clumping or getting stuck and keeps them moving smoothly and efficiently.

Simple Screen Swapping

Various options are available for easy screen changes including fast-action band clamps connecting bed and lid, and air-lift devices which are helpful in larger models. Lids are not generally needed for sorting whole flower, however.

Batch-Sorting Operation

Optional hoppers allow product to be staged for batch operation, much like surge hoppers before Bulk Bag Loaders. Being attached to the screener, they vibrate upon operation, preventing product from bridging and aiding flow.

Quick-Change Lids

For the occasional process that requires a lid, there are a few clamshell lid options available. For smaller units, hinged lids can be fitted with quick-release band clamps with or without center-tensioning. Larger units can come equipped with air-lift devices for easy, single-person operation.

Related Products

More Hemp Drying Equipment

Showing 1–4 of 12 results

Contact Us

Reach out for a quote, more information, or just to talk about your process. We love discussing new ideas and want to hear about your application.

Visit Us

13911 NW 3rd Ct.

Vancouver, WA 98685

Contact us

(503) 248-0711

frontdesk@abmequipment.com

Open Hours

M-F: 8am – 5pm